YAMAHA DM 2000 GENERAL SPECIFICATIONS

Internal Signal Processing

32-bit (Accumulator 58-bit)

Sampling Frequency

Internal
External

44.1 kHz,48 kHz,88.2 kHz,96 kHz
Normal rate 44.1 kHz -10% - 48 kHz+6%
Double rate 88.2 kHz -10% - 96 kHz+6%

Signal Delay

Less than 2.3ms CH INPUT to STEREO OUT
(@Sampling frequency = 48 kHz)
Less than 2.2ms CH INPUT to STEREO OUT
(@Sampling frequency = 96 kHz)

Fader

motorized, touch sensitive: 100mm x 25

Fader Resolution                        

0 / -96 / infinity dB (256 steps/100mm) master faders
+10 / -72  / infinity dB (256 steps/100mm) other faders
0 / -96 / infinity dB (256 steps/100mm) stereo faders

Total Harmonic
Distortion
                  Input Gain = Min.

Less than 0.05% 20Hz to 20 kHz @+14dB into 600 W
Less than 0.01% 1 kHz @+18dB into 600 W
                  CH INPUT to STEREO OUT
                  Less than 0.05% 20Hz to 20 kHz @+14dB into 600 W
Less than 0.01% 1 kHz @+18dB into 600 W
                  CH INPUT to STEREO OUT

Frequency Response       

0.5,-1.5dB 20Hz - 20 kHz @+44dB onto 600 W
                  (@Sampling frequency = 48 kHz)
                  0.5,-1.5dB 20Hz - 20 kHz @+44dB onto 600 W
                  (@Sampling frequency = 48 kHz)

Dynamic Range
(maximum level to noise level)

110dB typ. DA Converter (STEREO OUT)
108dB typ. AD+DA (to STEREO OUT) 

Hum & Noise*
                  
Rs = 150W
Input Gain = Max.
Input Pad = 0dB
Input Sensitivity = -60dB

-128dB Equivalent Input Noise.
(20Hz-20kHz)
-94dB residual output noise. STEREO OUT
STEREO OUT off.

-94dB(98dB S/N) STEREO OUT
STEREO fader at nominal level and
all CH INPUT faders at minimum level.
-64dB (68dB S/N) STEREO OUTPUT
STEREO fader at nominal level and
all CH INPUT faders at minimum level.

Maximum Voltage Gain 

74dB CH INPUT (CH1-24) to STEREO OUT / OMNI (BUS) OUT
74dB CH INPUT (CH1-24) to OMNI (AUX) OUT (via pre input fader)
74dB CH INPUT (CH1-24) to CONTROL ROOM MONITOR OUT
(via STEREO bus)

Crosstalk (@1 kHz)

80dB adjacent input channels (CH1-24)
80dB input to output.

Power Requirements

U/C 120V  300W  60Hz

Dimensions

Height 257mm
Depth  810mm (with front pads)
Width  900mm

Net Weight

40kg

Operating free-air
temperature range

10-35^oC

Storage temperature range

-20-60^oC

*Hum & Noise are measured with a 6dB/octave filter @12.7 kHz;
equivalent to a 20 kHz filter with infinite dB/octave attenuation.
*Input Gain = Min.
*Total Harmonic Distortion is measured with a 6dB/octave filter @80kHz

Effect libraries (EFFECT1-8)

Number of factory presets
Number of user libraries

52 (EFFECT3-8 :43)
76

Compressor libraries

Number of factory presets
Number of user libraries

36
92

Gate libraries

Number of factory presets
Number of user libraries

4
124

EQ libraries

Number of factory presets
Number of user libraries

40
160

Channel libraries

Number of factory presets
Number of user libraries

2
127

GEQ libraries (EQ1-6)

Number of factory presets
Number of user libraries

1
128

Surround Monitor libraries

Number of factory presets
Number of user libraries

1
32

Input patch libraries

Number of factory presets
Number of user libraries

1
32

Output patch libraries

Number of factory presets
Number of user libraries

1
32

Bus to stereo libraries

Number of factory presets
Number of user libraries

1
32

Input
Terminals

GAIN

Actual Load
Impedance

For Use With
Nominal

Input level

Connector in

Sensitivity*1

Nominal

Max. before clip

Console

CH INPUT
A/B 1-24

0

-60dB

3K ohm

50-600 ohm
&
600 ohm Lines

-70dB
(0.245mV)

-60dB
(0.775mV)

-46dB
(3.88mV)

A:XLR-3-31
type
(Balanced)*2

26

-16dB

-26dB
(38.8mV)

-16dB
(0.123V)

-2dB
(616mV)

B:Phone
Jack
(TRS)
(Balanced)*3

0db
(775mV)

+10dB
(2.45V)

+24dB
(12.28V)

INSERT IN 1-24

10k ohm

600  ohm Lines

-6dB
(388mV)

+4dB
1.23V)

+18dB
(6.16V)

Phone
Jack
(TRS)
(Balanced)*3

2TR IN ANALOG 1(L,R)

10k ohm

600  ohm Lines

+4dB
(1.23V)

+4dB
1.23V)

+18dB
(6.16V)

Phone Jack
(TRS)
(Balanced)*3

2TR IN ANALOG 2(L,R)

10k ohm

600  ohm Lines

-10dB
(0.316V)

-10dB
(0.316V)

+4dBV
1.58V)

RCA Pin
Jack
(Unbalanced)

*1. Sensitivity is the lowest level that will produce an output of +4dB(1.23) or the nominal output level when the unit is
      set to maximum gain.(all faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1/Sleeve = GND, 2/Tip = HOT, 3/Ring = Cold)
*3 Phone jacks are balanced. (Tip  = HOT, Ring = GND,  Sleeve = GND)

• In these specifications, when dB represents are specific voltage, 0dB is referenced to 0.775 Vrms.
• For 2TR IN ANALOG 2 levels, 0bBV is referenced to 1.00 Vrms.
• All 24 AD converters (CH1-24) are 24 bit linear, 128 times oversampling.
• +48 DC (phantom power) is supplied to CH INPUT (1-24) XLR type connectors via each individual switch.

Output
Terminals

GAIN
SW

Nominal

Max. before clip

Stereo Out (L,R)

600 ohm

-

-10dBV(0.316V)

+4dbV(1.58V)

RCA Pin Jack
(Unbalanced)

150 ohm

-

+4dB(1.23V)

+18dB(6.16V)

XLR-3-32 type
(Balanced)*1

STUDIO
MONITOR
OUT (L,R)

+4dB(1.23V)

+18dB(6.16V)

Phone Jack (TRS)
(Balanced)*2

C-R MONITOR OUT LARGE (L,R)

150 ohm

600  ohm Lines

-

+4dB(1.23V)

+18dB(6.16V)

XLR-3-32 type
(Balanced)*1

C-R MONITOR OUT SMALL (L,R)

150 ohm

600  ohm Lines

-

+4dB(1.23V)

+18dB(6.16V)

XLR-3-32 type
(Balanced)*1

OMNI OUT 1-8

150 ohm

10k  ohm Lines

+18dB
(default)

+4dB(1.23V)

+18dB(6.16V)

Phone Jack (TRS)
(Balanced)*2

+4dB

-10dB(0.245V) 

+4dB(1.23V)

INSERT OUT 1-24

600 ohm

10k  ohm Lines

+4dB(1.23V)

+18dB(6.16V)

Phone Jack (TRS)
(Balanced)*2

PHONES

100 ohm

8  ohm
Lines

-

4mW

25mW

Stereo Phone Jack (TRS) (Unbalanced)*3

40 ohm
Lines

-

12mW

75mW

*1. XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = Cold)
*2. Phone jack are balanced. (Tip = HOT, Ring = COLD, Sleeve = GND)
*3. PHONES stereo phone jack is unbalanced.
      (Tip = LEFT, Ring = RIGHT, Sleeve = GND)

• STEREO OUT (L,R), 0dBV is referenced to 1.00 Vrms.
• In these specifications, when dB represents are specific voltage, 0dB is referenced to 0.775 Vrms.
• All output (except INSERT OUT 1-24) DA converters are 24 bit, 128 times oversampling.

Terminal

Format

Data length

Level

Connector in Console

2TR IN DIGITAL

1

AES/EBU

24 bit

RS422

XLR-3-31 type (balanced)*2

2

AES/EBU

24 bit

RS422

XLR-3-31 type (balanced)*2

3

IEC-60958

24 bit

0.5Vpp/75

RCA Pin Jack

CASCADE IN

-

-

RS422

D-SUB Half Pitch Connector 68P (Female)

*1. DIGITAL IN 1-3
      DE-EMPHASIS is automatically processed when input signal contains emphasis
*2. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)

Terminal

Format

Data length

Level

Connector in Console 

2TR OUT DIGITAL

1

AES/EBU*1
Professional
use

24 bit*3

RS422

XLR-3-31 type (balanced)*4

2

AES/EBU*1
Professional
use

24 bit*3

RS422

XLR-3-31 type (balanced)*4

3

IEC-60958*2
Consumer
use

24 bit*3

0.5Vpp/75 ohm

RCA Pin Jack

CASCADE OUT

-

-

RS422

D-SUB Half Pitch Connector 68P (Female)

*1. channel status of DIGITAL OUT 1,2

type
emphasis
sampling rate

: 2 audio channels
: NO
: depends on the internal configuration

*2. channel status of DIGITAL OUT 3

type
category code
copy prohibit
emphasis
clock accuracy
sampling rate

: 2 audio channels
: 2 channel PCM encoder/decoder
: NO
: NO
: Level II (1000 ppm)
: depends on internal configuration

*3. dither

: word length 16 - 24 bit

*4 XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)

Yamaha

Maker

Model

Function

IN

OUT

Format

Res / Freq

Connector

Note

Yamaha

MY8-AT

Digital I/O

8

8

ADAT

20bit 44.1/48kHz

Toslink x 2

Can handle 24 bit/96 kHz by double channel mode

MY8-AE

Digital I/O

8

8

AES/EBU

24bit 44.1/48kHZ

D-sub 25pin

Can handle 24 bit/96 kHz by double channel mode

MY8-TD

Digital I/O

8

8

TDIF

24bit 44.1/48kHZ

D-sub 25pin

Can handle 24 bit/96 kHz by double channel mode

MY4-AD

A to D In

4

-

-

24bit 44.1/48kHZ

XLR x 4

MY4-DA

D to A Out

-

4

-

20bit 44.1/48kHZ

XLR x 4

MY8-mLAN

mLAN
Interface

8

8

IEEE
1394

24bit 44.1/48kHZ

1394 6pin

Maximum 5 Nodes

MY8-AD96

A to D In

8

-

-

24bit 44.1/48/88.2/96kHz

D-sub 25pin

MY8-DA96

D to A Out

-

8

-

24bit 44.1/48/88.2/96kHz

D-sub 25pin

MY8-AE96S

Digital I/O

8

8

AES/EBU

24bit 44.1/48/88.2/96kHz

D-sub 25pin

Sampling Rate Converter for Input, 3 cards max. with DM2000

MY8-AE96

Digital I/O

8

8

AES/EBU

24bit 44.1/48/88.2/96kHz

D-sub 25pin

Third Party

Maker

Model

Function

IN

OUT

Format

Res/Freq

Connector

Note

Waves

Y56K

Effect & I/O

8

8

ADAT

24bit 44.1/48kHZ

Toslink x 2

Check instructions for multiple use

Apogee

AP8AD

A to D In

8

-

-

24bit 44.1/48/88.2/96kHz

D-sub 25pin

Check instructions for multiple use

AP8DA

D to A out

-

8

-

24bit 44.1/48/88.2/96kHz

D-sub 25pin

Check instructions for multiple use